+++ /dev/null
-Summary
-
- This document describes the correlation between publicly documented
- logic, I/O, and routing resources within the Atmel AT40k/94k family
- of chips and bits in the bitstreams needed to program them.
-
- Our goal is to make this information available to the public without
- restriction on its use, for the purpose of creating automated tools
- which generate bitstreams.
-
-
-Statement of Public Knowledge
-
- The Knowledge encapsulated in this document was derived by formal
- scientific experimentation, using only information generally
- available to the public. Extreme care which has been taken to
- ensure that the process did not violate any copyright, trademark,
- trade secret, or patent statutes. No licensing contracts or
- non-disclosure agreements were entered into by the parties involved
- in this endeavor, nor did they have access to any confidential
- information.
-
- This document is part of the Public Domain; its authors surrender
- claim to copyright on it.
-
-
-Corrections
-
- If you find errors in this document, please correct them and add the
- date and a short description of the correction to the table below.
- This will assist in merging changes made in disjoint derivitaves.
-
- 2005.08.12 [gosset] Initial revision
- 2006.03.12 [megacz] Swapped {L1,L0}->W, FB->{L0,L1}, {H0->L0,H1->L1}
- 2006.03.13 [megacz] Fixed lowest bit of z=00000000; it should be "1"
- 2006.03.13 [megacz] Corrected meaning of z-octet bits 2-4 in IOBs
- 2006.03.13 [megacz] Added constant zeroes in IOB section
- 2006.04.15 [megacz] un-swapped FB->{L0,L1}
-
-Background
-
- The Atmel AT40k Datasheet describes in great detail the resources
- available in the AT40k as well as the FPGA portion of the AT94k
- (which is functionally identical and uses the same binary
- configuration format).
-
- The configuration space used to control these resources consists of
- a collection of independent octets arranged in a sparse 24-bit
- address space. This document correlates those bits with the
- resources described in the Datasheet.
-
- The process of configuring the device consists of writing these
- octets into the configuration memory. Once the desired
- configuration octets are known, the procedures for loading them into
- configuration memory are well documented in Atmel Documents 1009 and
- 2313.
-
- Each data octet "D" has a 24-bit address, divided into three address
- octets "X", "Y", and "Z". In general, the X and Y address octets
- are related to the physical position of the resource, while the Z
- octet is related to the type of resource being addressed.
-
-Notation
-
- We will use the notation A->B to indicate that setting the
- corresponding configuration bit high causes source A to drive wire
- B, and the notation A<>B to indicate that a pass gate between A and
- B is enabled. The notation ~A or ~A->B indicates a configuration
- bit controlling A or causing A to drive B is *active low*
- (inverted).
-
- We will use the following terms to describe routing resources.
- They vary slightly from Atmel's documentation, but are less
- ambiguous.
-
- X, Y, W, Z The cell's inputs
- XO, YO The X and Y outputs from the cell (to its neighbors)
- N, S, E, W Orthogonal lines: connections to neighboring cells
- NE,SE,NW,SW Diagonal lines: connections to neighboring cells
- S0..S4 Quad lines: four-cell long routing lines
- H0..H4 Horizontal quad lines
- V0..V4 Vertical quad lines
- L0..L4 Switchbox ports: the wires joining FB,H0..H4,V0..V4,X,Y,Z,W
- G0a..G4b Global lines: eight-cell long routing lines, in two sets (a+b)
- FB The cell's internal feedback line
- R The cell's internal register
- C The cell's "center" output; can drive the X or Y outputs
- ZM The "Z-mux"; the mux which drives the cell's register input
- WM The "W-mux"; the mux which drives the third input to the LUTs
- XL, YL The output of the X,Y-LUTs
- IA The "internal and" gate (W & Z)
-
-
-Cartesian Resources
-
- Although the exact interpretation of the X and Y octets depends on
- the resource type (Z octet), in most cases the X and Y octets are
- the cartesian coordinates of the logic cell nearest to the desired
- resource (0,0 is the lower-left hand logic cell). This section
- describes the significance of the Z and D octets for such resources.
-
- Notes:
- - The most significant four bits of the Z octet are 0000 for these bits
- - If WZ->WM and FB->WM are both low, then W->WM.
- - If ZM->R and YL->R are both low, then the XL->R
- - The ZM->C and ZM->FB bits are used to bypass the register (when high).
- - ~SET bit controls the set/reset behavior of the register; 0=set, 1=reset
-
- +----+--------+--------+--------+--------+--------+--------+--------+--------+
- |Z3:0| D octet |
- +----+--------+--------+--------+--------+--------+--------+--------+--------+
- |0000| V4->L4 | H4->L4 | FB->L2 | FB->L3 | FB->L1 | FB->L0 | FB->L4 | 1 |
- +----+--------+--------+--------+--------+--------+--------+--------+--------+
- |0001| ZM->R | YL->R | WZ->WM | FB->WM | ZM->C | ZM->FB | C->XO | C->YO |
- +----+--------+--------+--------+--------+--------+--------+--------+--------+
- |0010| L4->Z | L4->Y | L3->Z | L2->Z | L1->Z | L0->Z | V4->OE | H4->OE |
- +----+--------+--------+--------+--------+--------+--------+--------+--------+
- |0011| L2->W | L3->W | L4->W | L4->X | L0->W | L1->W |H2a<>V2a|H3b<>V3b|
- +----+--------+--------+--------+--------+--------+--------+--------+--------+
- |0100| N->Y | S->Y | W->Y | E->Y | L0->Y | L1->Y | L2->Y | L3->Y |
- +----+--------+--------+--------+--------+--------+--------+--------+--------+
- |0101| SW->X | NE->X | SE->X | NW->X | L0->X | L1->X | L2->X | L3->X |
- +----+--------+--------+--------+--------+--------+--------+--------+--------+
- |0110| X-LUT truth table, inverted |
- +----+--------+--------+--------+--------+--------+--------+--------+--------+
- |0111| Y-LUT truth table, inverted |
- +----+--------+--------+--------+--------+--------+--------+--------+--------+
- |1000| V3->L3 | H3->L3 | H2->L2 | V2->L2 | V1->L1 | H0->L0 | V0->L0 | H1->L1 |
- +----+--------+--------+--------+--------+--------+--------+--------+--------+
- |1001|H1a<>V1a|H0a<>V0a|H0b<>V0b|H4a<>V4a|H4b<>V4b|H1b<>V1b|H3a<>V3a|H2b<>V2b|
- +----+--------+--------+--------+--------+--------+--------+--------+--------+
- ...
- +----+--------+--------+--------+--------+--------+--------+--------+--------+
- |0001| 1 | 1 | 1 | 1 | ~SET | 1 | 1 | 1 |
- +----+--------+--------+--------+--------+--------+--------+--------+--------+
-
-
-Sector Resources
-
- Clocking, reset, and inter-sector repeaters are resources which are
- not specific to a particular cell. As such, their X,Y addressing is
- slightly different. These resources are addressed by the cartesian
- coordinates of the cell above or to the right of the resource, with
- an additional twist: for resources in vertical channels, the
- X-coordinate is shifted right by two bits (divided by four); for
- resources in horizontal channels, the Y-coordinate is shifted right
- by two bits (divided by four).
-
- The most significant three bits of the Z-octet for a sector resource
- are set to 001; the next bit (fourth most significant) is set to 0
- for horizontal channels and 1 for vertical channels.
-
- One sector wire and one global wire enter each side of each
- repeater, for a total of four connections. Each connection has an
- associated four-bit code which indicates if that connection is
- driven by the repeater, and if so, which connection to the repeater
- is used to drive it:
-
- 000 - driver disabled
- 100 - source is global wire on the other side of the repeater
- 010 - source is sector wire on the other side of the repeater
- 001 - source is other connection on the same side of the repeater
-
- Example: a code of 001 for the left-hand side sector wire driver
- means that the source of the driver should be the left hand side
- global wire. A code of 010 for the top sector wire driver means that
- the source of the driver should be the bottom sector wire.
-
- CC = column clock
- CR = column reset
- SC = sector clock
- CC+ = sector clock of the sector below this one
- InvSC = invert the clock source (CC or S4) before driving SC
-
- +----------+--------+--------+-----+-----+------+-----+-----+------+
- | Z octet | D octet |
- +----------+--------+--------+-----+-----+------+-----+-----+------+
- | 001_0000 | 1 | 0 | Left/Top G4 | Left/Top S4 |
- +----------+--------+--------+-----+-----+------+-----+-----+------+
- | 001_0001 | 0 | S4->CR | Right/Bottom G4 | Right/Bottom S4 |
- +----------+--------+--------+-----+-----+------+-----+-----+------+
- | 001_0010 | 1 | 0 | Left/Top G3 | Left/Top S3 |
- +----------+--------+--------+-----+-----+------+-----+-----+------+
- | 001_0011 | 1 | 1 | Right/Bottom G3 | Right/Bottom S3 |
- +----------+--------+--------+-----+-----+------+-----+-----+------+
- | 001_0100 | 1 | 0 | Left/Top G2 | Left/Top S2 |
- +----------+--------+--------+-----+-----+------+-----+-----+------+
- | 001_0101 | SC->CC+| S3->SC | Right/Bottom G2 | Right/Bottom S2 |
- +----------+--------+--------+-----+-----+------+-----+-----+------+
- | 001_0110 | 1 | 0 | Left/Top G1 | Left/Top S1 |
- +----------+--------+--------+-----+-----+------+-----+-----+------+
- | 001_0111 | 1 | 1 | Right/Bottom G1 | Right/Bottom S1 |
- +----------+--------+--------+-----+-----+------+-----+-----+------+
- | 001_1000 | 1 | 0 | Left/Top G0 | Left/Top S0 |
- +----------+--------+--------+-----+-----+------+-----+-----+------+
- | 001_1001 | InvSC |~SC->CC+| Right/Bottom G0 | Right/Bottom S0 |
- +----------+--------+--------+----+--------+----+-----+--------+---+
-
-
-Block Memories
-
- Although block memories are shown in the lower right hand corner of
- each sector in the Atmel Datasheets, they are conceptually addressed
- by the cartesian coordinate of the cell in the lower *left* hand
- corner of the sector. Furthermore, both coordinates are shifted
- right two bits (divided by four).
-
- The significance of the "D" octet for a given block memory depends
- on its position; if it falls in an odd sector-column (4-7, 12-15,
- etc), use the first chart; otherwise, use the second chart.
-
- USECLK = the memory is synchronous
- ENABLE = the memory is enabled
- DUAL = enable both ports on a dual-ported memory
-
- Odd Sector-Columns
-
- +--------+------+------+------+------+--------+--------+--------+---------+
- |Z octet | D octet |
- +--------+------+------+------+------+--------+---------+--------+--------+
- |01000000| 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 |
- +--------+------+------+------+------+--------+---------+--------+--------+
- |01000001| 1 | 1 | 1 | 1 | USECLK | ~ENABLE | ENABLE | ENABLE |
- +--------+------+------+------+------+--------+---------+--------+--------+
-
- Even Sector-Columns
-
- +--------+------+------+------+------+--------+--------+--------+--------+
- |Z octet | D octet |
- +--------+------+------+------+------+--------+--------+--------+--------+
- |01000000| 1 | 1 | 1 | 1 | USECLK | DUAL | ~DUAL | ENABLE |
- +--------+------+------+------+------+--------+--------+--------+--------+
- |01000001| 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 |
- +--------+------+------+------+------+--------+--------+--------+--------+
-
-
-I/O Blocks
-
- The Z octet for I/O resources always its most significant three bits
- set to 011. The next bit is 1 for North/South IO Blocks and 0 for
- East/West IO Blocks. The next bit is always 0, and the bit
- following that is set to 0 for primary (orthogonally connected)
- IOBs, 1 for secondary (diagonally connected) IOBs.
-
- S = Sector wires of this cell
- S+ = Sector wires of next cell
- S- = Sector wires of previous cell
- G = Global wires of this cell
- G+ = Global wires of next cell
- Output = Allow output from this IOB
- OE = when low, output is always enabled
- OEM = 7 bits, one-hot encoded, chooses input to output-enable mux
- USEOEM = when low, ignore the output enable mux
- Delay = amount of delay to add; can be 0, 1, 3, or 5
- Slew = slew time: 11=fast, 10=med, 01=slow
- Pull = 00=pullup, 11=pulldown, 01=none
-
- +--------+--------+--------+------+-------+-------+--------+--------+--------+
- |Z octet | D octet |
- +--------+--------+--------+------+-------+-------+--------+--------+--------+
- |011_0_00| Schmit | Slew |~G2->CR| 0 | Pull | 0 |
- +--------+--------+--------+------+-------+-------+--------+--------+--------+
- |011_0_01|REG->OUT| 0 | OE | Output Mux |
- +--------+--------+--------+------+-------+-------+--------+--------+--------+
- |011_0010| Added Delay (primary) |PRI->S-| PRI->G+| PRI->G | PRI->S |
- +--------+--------+--------+------+-------+-------+--------+--------+--------+
- |011_0110| Added Delay (secondary) |SND->S | SND->S+|PRI->REG|SND->REG|
- +--------+--------+--------+------+-------+-------+--------+--------+--------+
- |011_0_11| OEM | USEOEM | OEM |
- +--------+--------+--------+------+-------+-------+--------+--------+--------+
-
-
-Global Clock/Reset Networks
-
- To drive a column clock from one of the eight global clock/reset
- networks, set the corresponding bit in the desired column:
-
- +--------+--------+--------+
- |Z octet |X octet |Y octet |
- +--------+--------+--------+-----+-----+-----+-----+-----+-----+-----+-----+
- |10100000| column |00000000| CK1 | CK2 | CK3 | CK4 | CK5 | CK6 | CK7 | CK8 |
- +--------+--------+--------+-----+-----+-----+-----+-----+-----+-----+-----+
-
-Unknown
-
- The following configuration resources are not fully understood, but
- the values below appear to work.
-
- +--------+--------+--------+
- |Z octet |X octet |Y octet |
- +--------+--------+--------+-----+-----+-----+-----+-----+-----+-----+-----+
- | |00000000|00000000| 1 | 1 | 1 | 1 | 1 | 1 | GCK SRC |
- |10100001|00010111|00000000| 1 | 1 | 1 | 1 | 1 | 1 | GCK SRC |
- | |00101111|00000000| 1 | 1 | 1 | 1 | 1 | 1 | GCK SRC |
- +--------+--------+--------+-----+-----+-----+-----+-----+-----+-----+-----+
- |11010000|00000000|00000000| 1 | 1 | 0 | 0 | 0 | 0 | 0 | 0 |
- +--------+--------+--------+-----+-----+-----+-----+-----+-----+-----+-----+
- |11010011|00000000|00000000| 0 | 0 | 0 | 0 | 1 | 1 | 0 | 1 |
- +--------+--------+--------+-----+-----+-----+-----+-----+-----+-----+-----+
-
-
-
-
-
projects / slipway.git / blobdiff